Final Project.
For my final project I'm making a pinch pot. Recently from my projects there has been flowers on my projects that I have been making so I decided to make a flower on this. There will be a flower in the middle and circles moving around the flower.
Update: When I put it in the klim and the bottom part has exploded. I had a choice to put the pieces back on it but it was really difficult to do it. So I have went along from where is had its broken pieces and kept on going with it.
Update: When I put it in the klim and the bottom part has exploded. I had a choice to put the pieces back on it but it was really difficult to do it. So I have went along from where is had its broken pieces and kept on going with it.
Slab Project.
For my slap project im going to making a cube with a little 2 bridges crossing over each other on the top of the cube. For the design I was wanting to make water dripping down from the cube and little drops of water around the cube. My teacher has helped me made a 3D picture of it so that would help me make it. We had to grab some clay and wedge it. When we got done wedging it we had to slap it down to make it look flat, then we had to grab a rolling pin to make it more flatten. If you look at the square picture that is the base for the cube im going to be making. I can't wait to see the results when its done.
Update: I am almost done making my project all I have to do now is make the top bridges, make the design on it and glaze it.
Update: I am almost done making my project all I have to do now is make the top bridges, make the design on it and glaze it.
Coil Pots.
For my coil pot im going to be making this deisgn on my pot. After im done making it, im going to glaze it. This project seems pretty fun. The bottom part I have made a bowl then growing from that there are small balls then wavy lines. It will be going into a pattern until it hits 10 inches.
Pinch Pot.
For my pinch pot idea which is on the paper if you look at it, we had to make our very own design. What I was making for my design was have a flower on the pot with vines growing out of the flower going around the whole pot. I'm done with the pot, right now I'm working on the top part of the pot which is the tube. The tube part I was going to make diamonds on them. Once im done i'm going to be making the design and going to be painting/glazing it when I'm done. I'm really excited to see the results when im done with it.
Update: Im going to be making it smooth then will be making design on it. I'll be painting/glazing it when I'm done with it! (:
( I'm done with it, I put a clear glaze on it. I didn't put another coat on it, which I should of. That would of kept the glaze on it. That will give me another tip for next time though.)
Update: Im going to be making it smooth then will be making design on it. I'll be painting/glazing it when I'm done with it! (:
( I'm done with it, I put a clear glaze on it. I didn't put another coat on it, which I should of. That would of kept the glaze on it. That will give me another tip for next time though.)
Cylinder and A bowl.
For both of these projects I have made a bowl on the left side and on the right side I have made a cylinder. It looks easy, but it takes a lot of practice to get the hang of it. I'm going to be making one more. I really enjoying this project!
Update: I have finsihed my bowl and I have let it dry, it has cracked on the bottom and into the bowl when I looked inside of it. Hopefully it will be alright. I am done with the bowl and my cylinder. I have glazed my bowl and my cylinder and it looks really pretty, I'm pretty excited to see it when it gets fully done.
Update: I have finsihed my bowl and I have let it dry, it has cracked on the bottom and into the bowl when I looked inside of it. Hopefully it will be alright. I am done with the bowl and my cylinder. I have glazed my bowl and my cylinder and it looks really pretty, I'm pretty excited to see it when it gets fully done.